Half Off Ponds - PA-RP60P - Subsurface Rocking Piston Aeration Compressor for Ponds and Lakes. The Half Off Ponds PA-RP60P Subsurface Rocking Piston Aeration Compressors are high flow, high capacity air compressors ideally suited for lake and pond bottom aeration. Half Off Ponds Air Compressors operate on a 120-volt, 3.5-amp motor with a 6-foot double insulated power cord and are efficient in 25-foot water depths, with a maximum operating depth of 40 feet.
Air filter with replaceable, debris-trapping element delivers clean, pure air. These reliable, low maintenance units are designed for continuous or intermittent operation.
Sealed connecting rod and bearing lubrication, oil-free air compressing chamber and shock absorbing vibration isolating mounts assure years of trouble-free operation. The Half Off Ponds PA-RP60P Subsurface Rocking Piston Aeration Compressor is used to help break down fish waste allowing toxic gasses to harmlessly escape as well as helping prevent the pond surface from freezing over in the winter months by disrupting the water's surface. This is the perfect aerator to maintain and keep a healthy water feature.
Turnover is very important; moving water from the bottom to the surface reduces thermal layering and helps bring debris into suspension so the filtration system can remove and treat it. 3/8 Aeration Tubing is recommended with this compressor but NOT included. Half Off Ponds PA-RP60P - Subsurface Rocking Piston Aeration Compressor Includes. PA-RP60P - 1/2HP, 3.9 CFM Subsurface Rocking Piston Aeration Compressor. Air filter with replaceable element.
50 PSI pressure relief valve. Vibration-reducing rubber isolation mounts (x4). Half Off Ponds PA-RP60P 3.9 CFM Air Compressor for Pond and Lake Aeration. High flow, high capacity rocking piston air compressor delivers 3.9 cubic feet per minute (CFM) [at 5 PSI] maximum operating depth of 40 feet.Operating temperature range of -5 to 175 Degrees Fahrenheit with a overheat protection at 290 Degrees Fahrenheit. A Pump You Can Trust - Air filter with replaceable, debris-trapping element delivers clean, pure air. Dependable, reliable, low maintenance design for continuous or intermittent operation. Pump has aluminium allow body for maximum durability and copper motor for energy efficiency. Dimensions - 10 inches long, 6 inches wide, 7 inches high.
Includes air filter with replaceable element, 50 PSI pressure relief valve, and isolation mounts. 3/8 inch weighted air hose recommended (not included). 6-foot double insulated power cord.FAQs & Calculations to Help Select the Correct Kit. How Many Gallons of Water does My Water Feature Hold? Length x Width x Average Depth x 7.48 = Gallons Example: A rectangular pond 15' long, 10' wide and 1.5' Deep Pond is... 15' x 10' x 1.5' x 7.48 = 1683 Gallons.
Length x Width x Average Depth x 0.8 x 7.48 = Gallons Example: An oval pond 15' long, 10' wide and 1.5' deep is... Length x Width x Average Depth x 7.48 =Gallons Example: 15' long, 10' wide and 1.5' Deep Pond 15' x 10' x 1.5' x 7.48 = 1683 Gallons. Length x Width x Average Depth x 0.25 x 7.48 = GALLONS =Gallons Example: 15' long, 10' wide and 1.5' Deep Pond 15' x 10' x 1.5' x 7.48 = 1683 Gallons. How Big of a Pump Do I Need? Minimum pump size is determined by pond type, water volume, head height and friction loss.
The minimum pump size recommendations are. Water Garden, Few Small Goldfish. Circulate total pond water valoume every 2 hours.
Example: 2,000 GPH pump for a 3000-gallon pond with 2' waterfall. Fish Pond, Several Small Fish. Circulate total pond water valoume every 1 hour. Example: 3,800 GPH pump for a 3000-gallon pond with 2' waterfall. Koi Pond, Several Large Fish. Circulate total pond water valoume every 3/4 hours. Dynamic head pressure is found by taking the vertical height of your waterfall; the distance between where your pump is (typically in the skimmer) and where your waterfall is, and adding the static head pressure (pipe and fittings) 1' for every 10' of tubing and 1' for every elbow or "T" fitting. Example: 3' (vertical height) + 2.5 (25' of tubing) + 2' (for 2 elbows) = 7.5' of Dynamic Head Pressure Note: It is important to take into consideration while calculating how much flow will be at the top of your waterfall by accounting for the head height due to the laws of fluid dynamics. Please refer to the flow chart above to help choose the correct pump. What Size Tubing Do I Need? Customer service is our business. We have been satisfying fish pond, water garden, and backyard waterfall enthusiasts for over 25 years!We're glad to assist you with your pond building project - from start, to finish! The Half Off Ponds Team.